REPAIR & RENOVATION
AURORA FILLER
INSTANT MIX CEMENT ADHESIVE
EF00
Classic, dry mix filler which, once mixed with water, is ready for interior and exterior use. It dries to a firm, smooth and easily sanded material so this filler is ideal for use in filling and sealing plaster and cement wall cracks.
Application Areas
• Interior and exterior use.
• Used on plastered walls to fill small cracks, holes and other blemishes.
• Skim uneven surfaces to a smooth finish with NEO Aurora Filler.
• Plaster, hard board and
• Prepared, previously painted areas.
• Not suitable for cracks in substrates that are likely to continue to move (use NEO Repair Paste (nrp07) instead).
Product Features
• A quick drying, smooth crack filler.
• Excellent adhesion.
• Once sealed, can be top coated with a wide range of NEO Paints’ water and solvent based products.
• Dries to a firm, solid and flexible product.
• Once dry, the filler can be sanded easily to a smooth surface.
• NEO Aurora Filler, contrary to other makes of fillers, absorbs no humidity and water. This ensures
• NEO Aurora Filler should be applied with a flexible skimming blade. Once dry and solid, the surface must be sanded well until even and smooth.
• Sand glossy coatings well before applying.
• NEO Aurora Filler is based on a combination of mineral substances, which react and harden when mixed with water. Once dry, the minerals are hard and solid.
• The minerals contained in NEO Aurora Filler do not absorb the water, therefore the filler does not swell. This makes NEO Aurora Filler a rather unique and long-lasting quality product.
Application Details
| • Mixing | Mix into water until a stiff paste is formed. |
| • Application Method | Apply with a flexible skimming blade or paint scraper. |
| • Cleaning | Water. |
| • Application | • Mix NEO Aurora Filler into water until a stiff paste is formed. • Apply the resulting mixture with a flexible skimming blade or paint scraper. • Use up within 15-20 minutes. • When dry (1-2 hours), repeat the procedure until the crack, hole or blemish is properly filled. • After the last application, let the filled area dry over night (until the surface is firm). • Sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00). • Clean up application equipment immediately with water – difficult to remove when dry. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Surface Preparation
| • New / Raw Plaster • Precast |
• Plaster should be completely dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Mix NEO Aurora Filler into water until a stiff paste is formed. • Apply the resulting mixture with a flexible skimming blade or paint scraper. • Use up within 15-20 minutes. • When dry (1-2 hours), repeat the procedure until the crack, hole or blemish is properly filled. • After the last application, let the filled area dry over night (until the surface is firm). • Sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00). • Most contractors prefer to fill up holes and blemishes once the wall is primed for better visibility. • NEO Aurora Filler can be applied on emulsion based wall primers such as NEO Acrylic Wall Primer (ap00). |
| • Uncoated, Dry Concrete Surfaces | • Surface should be completely dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Mix NEO Aurora Filler into water until a stiff paste is formed. • Apply the resulting mixture with a flexible skimming blade or paint scraper. • Use up within 15-20 minutes. • When dry (1-2 hours), repeat the procedure until the crack, hole or blemish is properly filled. • After the last application, let the filled area dry over night (until the surface is firm). • Sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00). |
| • Uncoated, Weathered or New Fibre Cement Surfaces | • Remove dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Prime with NEO Acrylic Wall Primer (ap00). • Mix NEO Aurora Filler into water until a stiff paste is formed. • Apply the resulting mixture with a flexible skimming blade or paint scraper. • Use up within 15-20 minutes. • When dry (1-2 hours), repeat the procedure until the crack, hole or blemish is properly filled. • After the last application, let the filled area dry over night (until the surface is firm). • Sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00). |
| • Soft board, Hard board, Fibre board and Wood | • For use on wood and fibre board we recommend the use of our NEO Repair Paste (nrp07) only. |
| • Previously Painted Surfaces • Precast |
• Remove all loose, flaking and bubbling paint. • Remove all dust, foreign material, fungal and algae growth. • Allow to dry. • If then powdery or friable, seal with NEO Bonding Liquid (ig00). • NEO Aurora Filler can be applied directly on to PVA emulsion paint surfaces. • Eggshell or high gloss enamel paint surfaces should be sanded well before application. • Mix NEO Aurora Filler into water until a stiff paste is formed. • Apply the resulting mixture with a flexible skimming blade or paint scraper. • Use up within 15-20 minutes. • When dry (1-2 hours), repeat the procedure until the crack, hole or blemish is properly filled. • After the last application, let the filled area dry over night (until the surface is firm). • Sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00). |
Colour Range and Quantities
• NEO Aurora Filler is a white powder.
Available in 1kg, 2.5kg, 5kg and 25kg bags.
Precautions
• NEO Aurora Filler contains no toxic substances.
When mixed with water this product is mildly alkaline so avoid direct skin contact and wash off with water if it does occur.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
ELASTIC WATERPROOFING
EW00
New generation
Application Areas
• Interior and exterior use.
• Cement tiles (new or weathered), fibre cement sheeting (new or weathered), plaster, previously painted substrates.
• Primed metal and wooden substrates.
• Flat cement/concrete roofs.
• Seal nail heads and roofing bolts.
Product Features
• NEO Elastic Waterproofing is a coating material, which prevents water penetration into the substrate. Applied in several layers and strengthened with a suitable woven material it forms a thick protective membrane for roof sealing.
• NEO Elastic Waterproofing is available in several popular roof shades as well as white.
• NEO Elastic Waterproofing is based on a highly flexible and water resistant acrylic resin emulsion.
• Applied to specification it seals concrete roofs and prevents water penetration.
• NEO Elastic Waterproofing remains highly flexible for years even after extended exposure to the environment.
• Besides its main use on concrete roofs, NEO Elastic Waterproofing can be successfully applied on galvanised sheeting, roofing felt and fibre cement.
• The product can be used for replacing roofing felt completely. When NEO Elastic Waterproofing is applied directly on to wooden roof boards with suitable woven matting such as
• NEO Elastic Waterproofing is ideal for repair work on roofs such as sealing nail heads, leaking flashings and repairing damaged or cracked roofing felt.
• NEO Elastic Waterproofing can be used for the repair of leaking concrete or metal water dams and basins. Once the coating is properly dry and firm the coating is suitable for under water use.
• Highly durable and UV resistant.
• Highly water resistant.
• Excellent long term flexibility.
• Excellent adhesion.
• Quick drying – two coats can be applied in one day.
• Low odour.
• Three to four coats of NEO Elastic Waterproofing are used for best results.
• In white and pastel colours it also has the added benefit of being heat reflective and therefore reduces the temperature of the rooms (especially for metal roofs).
• If correctly applied to a properly prepared substrate the product has a life expectancy of 5-7 years, possibly longer.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | Brush or roller. |
| • Thinning | NEO Elastic Waterproofing is ready for use un-thinned; thinning with water will reduce its hiding power and effectiveness. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Three to four coats of NEO Elastic Waterproofing are used for best results. • With brush or roller, apply a generous/thick coat of NEO Elastic Waterproofing in small manageable sections. • Firmly and evenly press a layer of woven fabric waterproofing membrane such as Biddim into the wet layer of NEO Elastic Waterproofing. • Allow to dry 4-6 hours before recoating. • Apply a second, third and possibly a fourth generous coat, waiting 4-6 hours between coats, until the membrane is totally saturated and the surface has an even and very noticeable high sheen. • NEO Elastic Waterproofing is ready for use un-thinned; thinning with water will reduce its hiding power and effectiveness. • Clean up application equipment with clean tap water. • For application with woven fabric materials calculate at least one litre NEO Elastic Waterproofing per square metre substrate. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 3-4 square metres per litre for the first coat and 6-8 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Surface Preparation
| • Mild Steel (Renovation) | • Affected areas need to be cleaned back to bright metal and spot primed with NEO Corroguard (two coats in coastal regions). • With brush or roller, apply a generous/thick coat of NEO Elastic Waterproofing in small manageable sections. • Firmly and evenly press a layer of woven fabric waterproofing membrane such as Biddim into the wet layer of NEO Elastic Waterproofing. • Allow to dry 4-6 hours before recoating. • Apply a second, third and possibly a fourth generous coat, waiting 4-6 hours between coats, until the membrane is totally saturated and the surface has an even and very noticeable high sheen. |
| • Mild Steel (New) | • Degrease surfaces with NEO Metal Conditioner (mc00) to remove the manufacturer’s grease protective layer. This process is repeated until the surface is water break free. • After drying, the whole substrate is coated with NEO Corroguard (cg00). • With brush or roller, apply a generous/thick coat of NEO Elastic Waterproofing in small manageable sections. • Firmly and evenly press a layer of woven fabric waterproofing membrane such as Biddim into the wet layer of NEO Elastic Waterproofing. • Allow to dry 4-6 hours before recoating. • Apply a second, third and possibly a fourth generous coat, waiting 4-6 hours between coats, until the membrane is totally saturated and the surface has an even and very noticeable high sheen. |
| • Uncoated Cement, Concrete or Cement Tile Surfaces (e.g. Concrete Roofs) | • Make sure surface is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one thick, undiluted coat of NEO Elastic Waterproofing. • Firmly and evenly press a layer of woven fabric waterproofing membrane such as Biddim into the wet layer of NEO Elastic Waterproofing using a dry paint roller or similar tool. • Work only in sections as fabric must be applied on to the still wet NEO Elastic Waterproofing. • Apply a further two coats of NEO Elastic Waterproofing thickly on to the fabric, saturating it properly. • The woven fabric must be completely saturated until the surface has an even, glossy sheen. If this is not achieved, the contractor must apply additional coats of NEO Elastic Waterproofing. |
| • Uncoated Weathered or New Fibre Cement Surfaces and Roofing Felt | • Remove dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Remove any collected sand and dust. • Use a firm brush and soap water. • Rinse well with clean potable water. • With brush or roller, apply a generous/thick coat of NEO Elastic Waterproofing in small manageable sections. • Firmly and evenly press a layer of woven fabric waterproofing membrane such as Biddim into the wet layer of NEO Elastic Waterproofing. • Allow to dry 4-6 hours before recoating. • Apply a second, third and possibly a fourth generous coat, waiting 4-6 hours between coats, until the membrane is totally saturated and the surface has an even and very noticeable high sheen. |
| • Previously Painted Surfaces | • Surface must be in a sound condition. • Remove all loose, flaking and bubbling paint. • Remove all dust, foreign material, fungal and algae growth. • Allow to dry. • If then powdery or friable, seal with NEO Bonding Liquid (ig00). • Apply NEO Elastic Waterproofing as follows: • With brush or roller, apply a generous/thick coat of NEO Elastic Waterproofing in small manageable sections. • Firmly and evenly press a layer of woven fabric waterproofing membrane such as Biddim into the wet layer of NEO Elastic Waterproofing. • Allow to dry 4-6 hours before recoating. • Apply a second, third and possibly a fourth generous coat, waiting 4-6 hours between coats, until the membrane is totally saturated and the surface has an even and very noticeable high sheen. |
| • Repair of Leaks and Cracks in Water Dams | • Remove all dust, foreign material, fungal and algae growth from the metal, cement or plaster surface. • Concrete brick build dams must be completely dry. • For smaller damages, apply two coats of NEO Elastic Waterproofing as follows: • With brush or roller, apply a generous/thick coat of NEO Elastic Waterproofing in small manageable sections. • Firmly and evenly press a layer of woven fabric waterproofing membrane such as Biddim into the wet layer of NEO Elastic Waterproofing. • Allow to dry 4-6 hours before recoating. • Apply a second, third and possibly a fourth generous coat, waiting 4-6 hours between coats, until the membrane is totally saturated and the surface has an even and very noticeable high sheen. • Wait for 7 days before filling dam. |
Colour Range and Quantities
• NEO Elastic Waterproofing is available in a range of popular non-fade and UV resistant ready mixed pastel and darker
• Available in 1
Precautions
• NEO Elastic Waterproofing is not flammable.
• Contains no toxic substances and only low levels of VOC (EU regulations).
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
ISOLIERFARBE
SEALANT
IF00
NEO Isolierfarbe is a quick drying sealant for the sealing of previously stained areas to prevent the stains bleeding through the water or solvent based top coat. Because of NEO Isolierfarbe’s outstanding penetration, it gives excellent bonding adhesion of itself and subsequent topcoats.
Application Areas
• Interior and exterior use.
• Previously painted areas which are water, nicotine or soot-stained. Seal off before repainting can commence.
Product Data
| Resin Base | Air drying synthetic solution polymer |
| Drying Time | Touch dry: 15-20 minutes Hard dry: 1 – 2 hours |
| Solid Matter by Content | By volume: 30-32% By mass: 55-57% |
| Film Thickness | 40 microns |
| Spreading Rate | 5 – 8 square Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 5-6 square |
| Surface Appearance |
Product Features
• Quick drying.
• Excellent sealer for water stains on ceilings.
• Can be used to seal off old, deteriorated bitumen and tar substrates and roofing felt.
• Excellent adhesion to a range of surfaces including tempered hardboard/fiber-boards which are notoriously difficult to overcoat.
• Can be over-coated with a wide range of NEO Paints’ water and solvent-based topcoats.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | Brush or roller. Spray application is NOT possible. |
| • Thinning | NEO M-Thinners (mt01). |
| • Cleaning | NEO M-Thinners (mt01). |
| • Application | • Stir well before use. • Spray application is NOT possible. • Normally only one coat of NEO Isolierfarbe is required, however, for severely stained surfaces two coats may be required. • Apply a generous coat of NEO Isolierfarbe with brush or roller. • Allow to dry 2 hours before applying topcoat. • Can be over-coated with NEO Paints’ water or solvent based products. • Only apply in well ventilated areas, keep away from all ignition sources, flames and sparks. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 5-6 square metres per litre for the first coat and 7-8 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates. • Do not eat, drink or smoke while applying. • Do not apply before 09:00 and after 16:00 in the winter. • Clean up application equipment with NEO M-Thinners (mt01). • For thinning use NEO M-Thinners (mt01). |
Surface Preparation
| • New or Stained surfaces, including Bitumen and Tar products | • Only apply to dry substrates where the moisture content is less than 15%. • Remove all dust, loose particles, flaking and peeling coatings from the substrate; if soot or nicotine stains are present wash them off with hot soapy water. • Allow to dry. • Normally only one coat of NEO Isolierfarbe is required, however, for severely stained surfaces two coats may be required. • Spray application is NOT possible. • Apply a generous coat of NEO Isolierfarbe with brush or roller. • Allow to dry 2 hours before applying topcoat. |
Colour Range and Quantities
• NEO Isolierfarbe is available in White only.
• Available in 1 litre and 5 litres.
Precautions
• NEO Isolierfarbe is flammable.
• Use only in well ventilated areas.
• Avoid inhaling of solvent vapours.
• Do not eat, drink or smoke while applying.
• Do not apply to extremely alkaline substrates like fibre cement.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
BONDING LIQUID
IG00
NEO Bonding Liquid is a unique, water-based, penetrating, bonding and stabilizing liquid/sealer for interior and exterior use on powdery, friable and very porous new and weathered substrates such as limewash, old paint, new friable or porous plaster and fillers. Once the NEO Bonding Liquid has done its job these areas can be over-coated with a range of NEO Paints’ water and solvent based decorative products. NB: This product was previously known as NEO Isoliergrund.
Application Areas
• Interior and exterior use.
• New or weathered plaster and
• Powdery, friable, weathered, previously painted areas.
• Lime
Product Features
• Unique
• NEO Bonding Liquid is based on a resin emulsion and can therefore be diluted with water, which makes it a very cost effective product.
• NEO Bonding Liquid has a good alkaline resistance and can be u
• Once sealed can be top coated with a wide range of NEO Paints’ water and solvent based products.
• This product can be used as additional stabilizing agent for walls treated with NEO Salt Stop (ss10).
• Excellent penetrating and binding properties.
• Excellent adhesion.
Application Details
| • Mixing | Stir well before use. Thin with 10-25% clean water. |
| • Application Method | Apply with a paintbrush or roller. |
| • Thinning | Water. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • NEO Bonding Liquid has an excellent penetration ability which allows it to permeate deep into the substrate and strengthen it. • Apply NEO Bonding Liquid, thinned with 10-25% clean water depending on how porous the substrate is (more porous, more water), with brush or roller. • When dry (2-3 hours), repeat the procedure if required. • Allow to dry before over-coating with the required NEO Paints’ primer or topcoat. • Apply with a paintbrush or roller. • Clean up application equipment with clean tap water. • Do not apply before 9:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Surface Preparation
| • Uncoated dry porous concrete surfaces • Raw Plaster • Precast • Uncoated, Weathered or New Fibre Cement Surfaces |
• Remove dust, foreign material, fungal and algae growth. • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. |
| • Previously Painted Surfaces • Precast |
• Remove all loose, flaking and bubbling paint. • Remove all dust, foreign material, fungal and algae growth. • Lime wash coated walls: remove lime wash as far as possible with scraper blades and / or soft wire or hard fibre brushes but be careful not to damage the plaster. • Allow to dry. • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. |
Colour Range and Quantities
• Clear/semi translucent.
• Available in 1 litre and 5 litres.
Precautions
• NEO Bonding Liquid contains no toxic substances and low levels of VOC (EU regulations).
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
METAL CONDITIONER
MC00
A new generation cleaner for steel and galvanized steel, especially roofs.
Application Areas
• Interior and exterior use.
• Uncoated steel or galvanized steel roofs.
• Ideal for the preparation of new galvanized roof sheeting gutters, downpipes, and other galvanized metal.
• NEO Metal Conditioner is essential for the preparation of new galvanized metal for paint application.
Product Features
• NEO Metal Conditioner removes mineral oils and waxes from galvanised metal. The product etches the shiny metal surface slightly, resulting in a good adhesion of the paint coating. It is therefore ideal for the preparation of new galvanised roof sheeting, gutters, down pipes and other galvanised metal.
• When applied on steel, NEO Metal Conditioner etches away light rust deposits and removes grease and oily substances from the metal surface.
• It is very important that after the treatment all traces of NEO Metal Conditioner are removed with potable water from the metal surface.
• Easy to use.
• Non flammable.
• Washes off with water.
• NEO Metal Conditioner should not be seen as a chemical rust remover for heavily corroded areas. For such purpose we suggest NEO Rust Remover (rr00).
• In some instances there is still a prejudice that new galvanised sheeting must be treated with hydrochloric acid before paint application. This is completely unacceptable. The acid damages the zinc coating by dissolving a considerable amount of the metal. NEO Metal Conditioner is the ideal product for this purpose as it dissolves fat and grease. It also etches the galvanised surface slightly to improve the adhesion of the consecutive paint coatings.
Application Details
| • Application Method | By scrubbing or block brush, brush with fibre bristles or a broom (not paint brush). |
| • Thinning | • For mild steel with light rust, use NEO Metal Conditioner undiluted. • For galvanised steel, dilute the NEO Metal Conditioner (1 part) with clean drinking water (3 parts). |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Use NEO Metal Conditioner undiluted for purpose of removing corrosive matter from steel. • For use on galvanised metal, dilute NEO Metal Conditioner as follows: o 1 part NEO Metal Conditioner o 3 parts of water • Work NEO Metal Conditioner into the surface well with a scrubbing or block brush, brush with fibre bristles or a broom (not a paint brush). • Wash off/rinse all traces of NEO Metal Conditioner with copious amounts of clean water. • Repeat the washing process until the metal is grease (water break) free. • Allow to dry well before applying new paint. • Clean up application equipment and accidental spillage/stain with clean tap water. • When applying NEO Metal Conditioner, wear rubber gloves and goggles and avoid skin contact. • If skin contact occurs, wash off with copious amounts of clean water/soap. • Only use in well ventilated areas and avoid inhaling the vapours. |
Surface Preparation
| • Wood or Fibre Board | • The wood must be dry, seasoned and all knots and cracks sealed. • Prime wood with one coat of NEO Pink Primer. • Allow to dry for at least 24 hours. • Apply one coat of NEO Universal Undercoat (wu00). • Apply two final coats of any NEO Paints’ enamel paint. |
Colour Range and Quantities
• NEO Metal Conditioner is a clear, colourless liquid.
• Available in 1
Precautions
• NEO Metal Conditioner is not flammable.
• NEO Metal Conditioner contains acid.
• Handle with care.
• Wear rubber gloves and goggles when handling the product and avoid skin contact.
• If skin or eye contact occurs, wash off with copious amounts of clean water.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
GLUE FOR WOOD
NG00
NEO Glue is a high-quality wood glue made from a pure PVA emulsion. It contains no fillers.
Application Areas
• Interior and exterior use.
• NEO Glue can be used for all types of woodwork.
Suitable for use with all types of solid wood as well as most man-made fiber boards.
Product Features
• NEO Glue can be used for all types of woodwork. The glue dries quickly to a solid, hard and indestructible bond between the wooden components.
• NEO Glue is a universal product and suitable for some accelerated hardening methods.
• NEO Glue is based on a polyvinyl acetate emulsion and is a general-purpose type of wood glue.
• The glue dries to a firm bond within 30-60 minutes depending on temperature and moisture.
• NEO Glue is reasonably water resistant but should not be used for boat construction.
• NEO Glue should never be applied if temperatures are below +5degrees Celsius and not on cold winter mornings.
• For use with melamine sheeting and other synthetic materials, consult the NEO Paints technical department for advice.
Application Details
| • Application Method | Hand or machine application. |
| • Cleaning | Water. |
| • Application | • NEO Glue is suitable for hand or machine application. • Once dry, NEO Glue is unsoluble by water. |
Surface Preparation
| • Wood and Fibre board | • The surface must be completely dry. • Remove any fatty, greasy substances and dust from substrate. • Apply NEO Glue on both objects/surfaces to be bonded together. • Apply a moderate force with a vice or clamp for 45 minutes. |
Colour Range and Quantities
• NEO Glue is a white liquid that dries to a clear, transparent film.
• Available in the following sizes:
o 500 ml plastic bottles with spout
o 5 litre plastic bottles
o 20 litre plastic buckets
o 200 litre drums on request
Precautions
NEO Glue contains no harmful substances.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
REPAIR PASTE
MULTI-PURPOSE FILLER
NRP07
A ready-mixed flexible filler paste for interior and exterior use.
Application Areas
• Interior and exterior use.
• Use for cracks or holes in plaster, hardboard and fibre cement walls.
• Use for cracks or holes in prepared or previously painted areas.
• Can successfully be applied on wood, wood fibre and soft board.
• Excellent adhesion on different substrates such as plaster, concrete, wood, fibre board, soft board, fibre cement and metal surfaces.
• Can be used to seal small joints, flashings and nail heads on roofs and make them waterproof.
• Being water resistant, NEO Repair Paste can successfully be used for underwater repairs such as pools, water storage dams and containers.
• NEO Repair Paste should never come into direct contact with un-primed steel.
Product Features
• A highly flexible filler paste for use in and around the house. Cracks in walls filled and repaired with this filler can move and widen to a certain degree without being visible.
• A quick drying, flexible, smooth filler.
• Settles to a solid and highly flexible substance.
• The filler adheres well to the substrate and allows for a certain degree of movement.
• Once sealed, can be top coated with a wide range of NEO Paints’ water and solvent based products.
Application Details
| • Application Method | Flexible skimming blade or paint scraper. |
| • Cleaning | Water. |
| • Application | • Apply NEO Repair Paste with a flexible skimming blade or paint scraper. • When dry (2-3 hours), repeat the procedure until the crack / hole is properly filled. • After the last application, let the filled area dry over night (until the surface is firm) and sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00). • Do not apply before 9:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. • Clean up application equipment with water immediately – difficult to remove when dry. • Application has to be repeated as NEO Repair Paste shrinks to a certain degree. |
Surface Preparation
| • Uncoated, Dry Concrete Surfaces • Precast |
• Concrete should be completely dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Apply NEO Repair Paste with a flexible skimming blade or paint scraper. • When dry (2-3 hours), repeat the procedure until the crack / hole is properly filled. • After the last application, let the filled area dry over night (until the surface is firm) and sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00). |
| • Uncoated, Weathered or New Fibre Cement Surfaces | • Remove dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Prime with NEO Acrylic Wall Primer (ap00). • Apply NEO Repair Paste with a flexible skimming blade or paint scraper. • When dry (2-3 hours), repeat the procedure until the crack / hole is properly filled. • After the last application, let the filled area dry over night (until the surface is firm) and sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00) before applying topcoat. |
| • Raw Plaster | • Plaster should be completely dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Apply NEO Repair Paste with a flexible skimming blade or paint scraper. • When dry (2-3 hours), repeat the procedure until the crack / hole is properly filled. • After the last application, let the filled area dry over night (until the surface is firm) and sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00) before applying topcoat. |
| • Previously Painted Surfaces • Precast |
• Remove all loose, flaking and bubbling paint. • Remove all dust, foreign material, fungal and algae growth. • Allow to dry. • If then powdery or friable, seal with NEO Bonding Liquid (ig00). • NEO Repair Paste can be applied directly on to PVA emulsion paint surfaces. • Eggshell or high gloss enamel paint surfaces should be sanded well before application. • Apply NEO Repair Paste with a flexible skimming blade or paint scraper. • When dry (2-3 hours), repeat the procedure until the crack / hole is properly filled. • After the last application, let the filled area dry over night (until the surface is firm) and sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00) before applying topcoat. |
| • Soft board, Hard Board, Wood and Fibre boards | • NEO Repair Paste can be applied on such substrates for interior and exterior use. • Apply NEO Repair Paste with a flexible skimming blade or paint scraper. • When dry (2-3 hours), repeat the procedure until the crack / hole is properly filled. • After the last application, let the filled area dry over night (until the surface is firm) and sand to a smooth surface. • Carefully remove dust. • Seal with NEO Bonding Liquid (ig00) or NEO Acrylic Wall Primer (ap00) before applying topcoat. |
Colour Range and Quantities
• NEO Repair Paste is a white paste.
• Available in 500ml, 1
Precautions
• This product contains no toxic substances and very low levels of VOC (EU regulations).
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
PAINT REMOVER
PR00
A classic, highly effective, methylene chloride based paint remover.
Application Areas
• Interior and exterior use.
• Previously painted areas where the coating has to be removed.
• NEO Paint Remover is a highly effective paint remover for use on enamel paints, varnishes and other coatings. The paint remover lifts off several coating layers of paint at a time.
• NEO Paint Remover will have limited or no effect on PVA emulsion paints, two component coatings and chemical resistant finishes.
Product Features
• Highly effective against a range of paint and varnish types – removes several layers at once.
• NEO Paint Remover is a quick working paint remover, which lifts off existing old paint coatings from the substrate within minutes.
• NEO Paint Remover is a paste, which can be applied on vertical surfaces as well.
• About 10 to 20 minutes after application, the old paint varnish coatings will come loose and form bubbles. With the use of a paint scraper the old paint as well as remaining paint remover can be removed.
• Should there be many layers of old paint, this process might have to be repeated.
• It is very important to remove all traces of paint remover by means of rinsing well with warm water and soap before applying new paint.
• Easy to use.
• Non flammable.
• Washes off with water.
Application Details
| • Application Method | Brush application. Never apply NEO Paint Remover by spraying. |
| • Cleaning | Water and soap (dishwashing liquid). |
| • Application | • Stir well before use. • Brush a generous/thick coat of NEO Paint Remover on to the area that needs stripping in small manageable sections (lightly sand if the paint is very old or well cured to aid penetration). • Allow the material to stay in contact for 10 to 20 minutes until the paint starts bubbling and lifting. • Remove with a paint scraper. • For very thick or very old, cured coatings, apply a second generous application and repeat the waiting and scraping process. • Wash off/rinse all traces of NEO Paint Remover with copious amounts of warm water/soap. • Allow to dry well before applying new paint. • Clean up application equipment and accidental spillage/stain with clean tap water/dishwashing liquids. • When applying, wear gloves and goggles and avoid skin contact. If skin contact occurs, wash off with copious amounts of clean water/soap. • Avoid the vapours – only use in well ventilated areas. • By brush application only. • Never apply NEO Paint Remover by spraying. |
Surface Preparation
| • Previously Painted Surfaces | • Apply a generous/thick coat of NEO Paint Remover on to the existing paint coating. • Allow to react for 10 to 20 minutes. Then remove loose paint coatings and remaining paint remover with a paint scraper. • Rinse well with warm water and soap (dishwashing liquid) • Repeat if required. • Wooden substrates might require sanding before the application of new paint/varnish coatings. |
Colour Range and Quantities
• Semi-transparent, thick paste.
• Available in 500ml,1
Precautions
• NEO Paint Remover is not flammable.
• Avoid skin contact – wear rubber gloves for protection.
• Ventilate well – avoid inhaling
• Remove any stains immediately with warm water and soap.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
SALT STOP
SS30
NEO Salt Stop is a unique, water based, ultra deep, penetrating, bonding and stabilizing liquid/water repellent for interior and exterior plaster and concrete to prevent salts, water, and alkaline substances being transported to the surface. Once the NEO Salt Stop has done its job, these areas can be over-coated with a range of NEO Paints’ water-based decorative products.
Application Areas
• Interior and exterior use.
• New, damp, dry, weathered plaster and concrete walls.
• Powdery, friable, weathered, previously plastered areas.
Product Features
• Reduces the water and humidity absorption of masonry, concrete, unglazed bricks and tiles,
• Silicone resins penetrate deep into the substrate forming an invisible barrier. This prevents other substances and liquids from penetrating under the surface.
• NEO Silicone should be used as a preventive treatment and coating. Should salt and other minerals be present in the plaster or floor screed, NEO Salt Stop (ss30) should be used.
• NEO Silicone penetrates deep into the stonework and dries to an invisible coating. The product does not stain the substrate.
• Unglazed tiles become water repellent. NEO Silicone is ideal for treating terra cotta tiles,
• Kalksandsteine treated with NEO Silicone do not absorb rainwater and the
• Excellent penetrating, binding and water repellent properties.
• Excellent adhesion.
• Once sealed, can be top coated with a wide range of NEO Paints’ water and solvent based products.
• For exterior
• This product is not suitable for
Application Details
| • Mixing | Stir well before use. Dilute NEO Salt Stop 1 volume with 9 volumes clean water in glass or plastic (never metal) containers. |
| • Application Method | Clean brush only. |
| • Thinning | Water. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Dilute NEO Salt Stop 1 volume with 9 volumes clean water in glass or plastic (never metal) containers. • When applying NEO Salt Stop, wear gloves and goggles as diluted NEO Salt Stop is rather aggressive. If it comes in contact with skin, wash off with lots of clean water. • Apply using a clean brush only. The plaster or cement can be dry or damp. • When dry (after 24 hours), repeat the procedure. • Allow the treated plaster or cement to thoroughly dry/harden (3-4 weeks) before over-coating with the required NEO Paints’ primer or topcoat. • Clean up application equipment with water. • Use any diluted NEO Salt Stop within 6-8 hours, after that time period NEO Salt Stop is not useable. Do not keep overnight. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Surface Preparation
| • Uncoated dry porous concrete surfaces • Uncoated weathered or new fibre cement surfaces • Raw damp plaster/cement |
• Remove all dust, foreign material, fungal and algae growth. • Dilute NEO Salt Stop 1 volume with 9 volumes clean water in glass or plastic (never metal) containers. • When applying NEO Salt Stop, wear gloves and goggles as diluted NEO Salt Stop is rather aggressive. If it comes in contact with skin, wash off with lots of clean water. • Apply using a clean brush only. The plaster or cement can be dry or damp. • When dry (after 24 hours), repeat the procedure. • Allow the treated plaster or cement to thoroughly dry/harden (3-4 weeks) before over-coating with the required NEO Paints’ primer or topcoat. |
| • Old coatings/plaster-remove coatings / crumbling plaster | • Remove old paint coatings and crumbling plaster. • Prime substrate twice with NEO Salt Stop diluted to specification. • Allow to dry, then re-plaster. • Prime the plaster again with two coats of NEO Salt Stop while it is still damp. • Once the plaster is dry and solid, apply your final coats of NEO Dur (SABS 1586-1, Grade 1) (ep00). |
Colour Range and Quantities
• Clear/light brown.
• Available in 1
Precautions
• When diluted with water this product is a skin irritant. Gloves and goggles should be worn and skin contact avoided.
• If NEO Salt Stop comes in contact with skin, the area should be rinsed with clean water.
• Keep out of reach for children.
• The product is not flammable.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.