WALL PAINT
WALL PAINT
AURORA
ACRYLIC EMULSION
AE00
A new generation, water-based, 100% acrylic, quality interior/exterior, matt coating. Meets the rigorous requirements of SABS 1586-3, Grade 3.
Application Areas
• Economically priced emulsion paint based on an acrylic resin emulsion.
• Cleanable, comfortably meets the requirements of the very harsh SABS and ASTMS scrubs resistant test methods.
• Excellent adhesion to properly prepared substrates.
• Good opacity / hiding power.
• Low odour.
• Two coats of NEO Aurora are applied for best results.
• Combines good durability with a high degree of hiding power. Due to its high pigment content it fills up small cracks, holes and plaster blemishes.
• NEO Aurora dries to a completely even matt finish.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | Brush, roller or airless spray. |
| • Thinning | NEO Aurora is ready for use un-thinned; thinning with water will reduce its hiding power. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Two coats of NEO Aurora are applied for best results. • With brush, roller or airless spray, apply a generous coat of NEO Aurora. • Allow to dry 3-4 hours before recoating. • Apply a second generous coat of NEO Aurora. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. • NEO Aurora is ready for use un-thinned; thinning with water will reduce its hiding power. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 6-8 square metres per litre for the first coat and 8-10 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates. • Clean up application equipment with clean tap water. |
Surface Preparation
| • Uncoated Concrete Surfaces • Raw / New Plaster • Precast |
• Make sure surface is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Prime with NEO Acrylic Wall Primer (ap00). • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • With brush, roller or airless spray, apply a generous coat of NEO Aurora. • Allow to dry 3-4 hours before recoating. • Apply a second generous coat of NEO Aurora. |
| • Uncoated, Weathered or New Fibre Cement Surfaces | • Remove dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • With brush, roller or airless spray, apply a generous coat of NEO Aurora. • Allow to dry 3-4 hours before recoating. • Apply a second generous coat of NEO Aurora. |
| • Soft Board or Gypsum Board Ceilings • Hard Board • Cornices |
• Make sure substrate is clean and free from dust. * The application of a primer is not required on ceiling boards. |
| • Previously Painted Surfaces | • Surface must be in a sound condition. • Existing gloss finishes should be well sanded. • Remove all loose, flaking and bubbling paint. • Remove all dust, foreign material, fungal and algae growth. • Allow to dry. • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Prime the bare and visible plaster areas with NEO Acrylic Wall Primer (ap00). • With brush, roller or airless spray, apply a generous coat of NEO Aurora. • Allow to dry 3-4 hours before recoating. • Apply a second generous coat of NEO Aurora. |
Colour Range and Quantities
• NEO Aurora is available in a range of popular ready-mixed
• Available in a variety of pastel shades but not in deep or bright shades.
• Available in 5
Precautions
• NEO Aurora is not flammable.
• It contains no toxic substances and very low levels of VOC (EU regulations).
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
HOUSEHOLD PAINT
ACRYLIC EMULSION
AI00
A new generation, water-based, 100% acrylic, quality interior, matt coating.
Application Areas
• Interior use only.
• Plaster, hardboard and fibre cement walls.
• Ceilings, like soft board, gypsum and other fibre board.
• Cast concrete or plastered ceilings.
• Can be applied on new plaster, which still has high humidity content and is still very alkaline.
Product Data
| Resin Base | Acrylic resin emulsion |
| Drying Time | Touch dry: 30 minutes Hard dry: 3–4 hours |
| Solid Matter by Content | By volume: 28% By mass: 49.2% |
| Film Thickness | Approximately 40–60 microns |
| Spreading Rate | 6 – 10 square Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 6-8 square |
| Surface Appearance | Matt |
Product Features
• Economically priced emulsion paint based on an acrylic resin emulsion.
• Excellent adhesion to properly prepared substrates.
• Good opacity / hiding power.
• Low odour.
• Two coats of NEO Household Paint are applied for best results.
• Due to its high pigment content it fills up small cracks, holes and plaster blemishes.
• NEO Household Paint dries to a completely even matt finish.
Application Details
| • Mixing | AAlways stir well before use with a flat paddle. |
| • Application Method | Brush or roller application or airless spray. |
| • Thinning | NEO Household Paint is ready for use un-thinned; thinning with water will reduce its hiding power. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Two coats of NEO Household Paint are applied for best results. • With • Allow • Apply a second generous coat of NEO Household Paint. • Do not apply before 09:00 and after 16:00 in the winter. • NEO Household Paint is ready for use un-thinned; thinning with water will reduce its hiding power. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 6-8 square • For interior use only. • Clean up application equipment with clean tap water. |
Surface Preparation
| • Uncoated Concrete Surfaces | • Make sure surface is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Prime with NEO Acrylic Wall Primer (ap00). |
| • Raw / New Plaster | • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • With brush, roller or airless spray, apply a generous coat of NEO Household Paint. • Allow to dry 3-4 hours before recoating. • Apply a second generous coat of NEO Household Paint. |
| • Uncoated, Weathered or New Fibre Cement Surfaces | • Remove dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • With brush, roller or airless spray, apply a generous coat of NEO Household Paint. • Allow to dry 3-4 hours before recoating. • Apply a second generous coat of NEO Household Paint. |
|
• Soft Board or Gypsum Board Ceilings • Hard Board |
• Make sure substrate is clean and free from dust. * The application of a primer is not required on ceiling boards. |
| • Previously Painted Surfaces | • Surface must be in a sound condition. • Existing gloss finishes should be well sanded. • Remove all loose, flaking and bubbling paint. • Remove all dust, foreign material, fungal and algae growth. • Allow to dry. • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Prime the bare and visible plaster areas with NEO Acrylic Wall Primer (ap00). • With • Allow • Apply a second generous coat of NEO Household Paint. |
Colour Range and Quantities
• NEO Household Paint is available in White and limited pastel colours.
• Available in 20 litres.
Precautions
• NEO Household Paint is not flammable.
• It contains no toxic substances and very low levels of VOC (EU regulations).
Disclaimer
This product is not an acrylic primer and must not be used in place of NEO Acrylic Wall Primer (ap00) or failure will result.
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
CONTRACTOR PVA
CP00
Economically priced new generation water-based, matt coating for walls and ceilings.
Application Areas
• Interior and exterior use.
• Plaster, hardboard, fibre cement walls and ceilings.
• Housing projects, outside walls, garden walls, garages, sheds, storerooms, etc.
Product Features
• Good opacity / hiding power.
• Low odour.
• Two coats of NEO Contractor PVA are applied for best results.
• Highly alkaline resistant acrylic resin emulsion.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | Brush, roller or airless spray. |
| • Thinning | NEO Contractor PVA is ready for use un-thinned; thinning with water will reduce its hiding power. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Requires no prime coat and can be applied directly on to the substrate. • Can be applied on fresh plaster when still humid since the humidity can escape due to the high porosity of the paint coating. • Fills small holes and cracks due to its high solid matter content and resulting thick coating. • NEO Contractor PVA is ready for use un-thinned; thinning with water will reduce its hiding power. • Two coats of NEO Contractor PVA are used for best results. • Allow to dry 2-3 hours before recoating. • Clean up application equipment with clean tap water. • Can not be washed or cleaned with household cleaners or soap. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. • Under no circumstances should NEO Contractor PVA be used as a replacement for NEO Acrylic Wall Primer (ap00) or NEO Bonding Liquid (ig00) under any paint type. • Should not be used as a primer for high quality emulsion paints such as NEO Dur (ep00) or NEO Teflacryl (tc00). • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 6-8 square metres per litre for the first coat and 8-10 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates. |
Surface Preparation
| • New / Raw Plaster • Uncoated Concrete Surfaces |
• Make sure surface is firm and reasonably dry. • Remove all dust, foreign material, fungal and algae growth. • Repair any cracks, holes and other blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply two coats of NEO Contractor PVA. • Allow to dry 2-3 hours before recoating. |
| • Uncoated, Weathered or New Fibre Cement Surfaces | • Remove all dust, foreign material, fungal and algae growth. • If powdery or friable, seal with NEO Bonding Liquid (ig00). • Apply two coats of NEO Contractor PVA. • Allow to dry 2-3 hours before recoating. |
| • Softboard Ceilings • Hard Board |
• Prime nail heads with NEO Universal White Undercoat (wu00)(this will prevent corrosion of nail heads). • Repair any cracks and holes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply two coats of NEO Contractor PVA. • Allow to dry 2-3 hours before recoating. • For light coloured or pre-primed soft board ceilings, a two-coat application is usually sufficient, otherwise specify a third coat. |
| • Previously Painted Surfaces | • Do not apply NEO Contractor PVA on glossy or semi gloss enamel paint coatings even if they are sanded and prepared. • On existing PVA paint coatings, make sure old paint coating is firm and solid. • Remove all loose, flaking and bubbling paint. • Remove all dust, foreign material, fungal and algae growth. • Repair any cracks and holes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Allow to dry. • Apply two coats of NEO Contractor PVA. • Allow to dry 2-3 hours before recoating. |
Colour Range and Quantities
• NEO Contractor PVA is available in a limited range of popular,
• Available in 5 and 20
Precautions
• NEO Contractor PVA is not flammable.
• The product contains no toxic substances.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
DUR
SEMI-MATT ACRYLIC EMULSION
EP00
A new generation, water-based, 100% acrylic, long-life, interior/exterior, silky sheen coating. Meets the rigorous requirements of SABS 1586-1, Grade 1.
Application Areas
• Interior and exterior use.
• High traffic areas that need a highly washable and durable coating in a wide range of colours.
• Plaster, hardboard and
• Primed metal and wooden substrates.
• Walls, ceilings, fibre cement, galvanised gutters and down pipes, PVC pipes, fibre and hard board panels.
Product Features
• Highly durable and UV resistant.
• The coating surface is smooth and silky in appearance.
• Highly washable – comfortably meets the requirements of the very harsh SABS and ASTMS scrubs resistant test methods.
• The slightly glossy surface prevents dirt pickup and makes it easy to clean.
• Can be cleaned with any household detergent and by scrubbing if required.
• Excellent adhesion.
• Low odour.
• Two coats of NEO Dur are applied for best results.
• If correctly applied to a properly prepared substrate, the product has a life expectancy of 7-10 years, possibly longer.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | Brush, roller or airless spray. |
| • Thinning | NEO Dur is ready for use un-thinned; thinning with water will reduce its hiding power. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Two coats of NEO Dur are applied for best results. • With brush, roller or airless spray, apply a generous coat of NEO Dur. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Dur. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. • NEO Dur is ready for use un-thinned; thinning with water will reduce its hiding power. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 6-8 square metres per litre for the first coat and 10-12 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates. • Clean up application equipment with clean tap water. |
Surface Preparation
| • Mild Steel (Renovation) | • Affected areas need to be cleaned back to bright metal and spot primed with NEO Corroguard (cg00). • Sand existing coating. • With brush, roller or airless spray, apply a generous coat of NEO Dur. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Dur. |
| • Mild Steel (New) | • Degrease surfaces with NEO Metal Conditioner (mc00) to remove the manufacturer’s grease protective layer. This process is repeated until the surface is water break free. • After drying, the whole substrate is coated with NEO Corroguard (cg00). • Degreased, galvanised metal: due to its acrylic resin base, NEO Dur can be applied direct without primer (inland, not at the coast). • With brush, roller or airless spray, apply a generous coat of NEO Dur. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Dur. |
| • Uncoated Concrete Surfaces • Raw / New Plaster • Precast |
• Make sure surface is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Prime with NEO Acrylic Wall Primer (ap00). • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • With brush, roller or airless spray, apply a generous coat of NEO Dur. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Dur. |
| • Uncoated, Weathered or New Fibre Cement Surfaces | • Remove dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • With brush, roller or airless spray, apply a generous coat of NEO Dur. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Dur. |
| • Wall Partitioning, Soft Board, Gypsum Board, Fibre Board, Hard Board, Cornices (New & Renovation) | • Remove any loose particles and dust from substrate. • Prime nail heads with a coat of NEO Universal Undercoat (wu00) (this will prevent corrosion of nail heads). • Prime surface with one coat of NEO Acrylic Wall Primer (ap00). • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • With brush, roller or airless spray, apply a generous coat of NEO Dur. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Dur. |
| • Previously Painted Surfaces • Concrete • Precast • Plaster |
• Surface must be in a sound condition. • Existing gloss finishes should be well sanded. • Remove all loose, flaking and bubbling paint. • Remove all dust, foreign material, fungal and algae growth. • Allow to dry. • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Prime the bare and visible plaster areas with NEO Acrylic Wall Primer (ap00). • With brush, roller or airless spray, apply a generous coat of NEO Dur. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Dur. |
| • Wooden Surfaces and Chipboard | • Prime wooden surface with one coat of NEO Pink Primer (pi00). • With brush, roller or airless spray, apply a generous coat of NEO Dur. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Dur. |
Colour Range and Quantities
• NEO Dur is available in a range of popular,
• Available in 1
Precautions
• NEO Dur is not flammable.
• It contains no toxic substances and very low levels of VOC (EU regulations).
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
MICA PLAST
TEXTURED COATING
MP00
New generation water-based, interior/exterior, long-life, the flexible coating containing Mica.
Application Areas
• Interior and exterior use.
• Long-life exterior protection of buildings.
• Used as a feature on interior walls.
• Smooth, textured finish is highly decorative for plastered or cast ceilings.
• New or weathered cement tiles.
• New or weathered fibre cement sheeting.
• New or weathered plaster.
• Previously painted substrates.
• Primed metal and wooden substrates.
Product Data
| Resin Base | Pure acrylic resin emulsion |
| Drying Time | Touch Hard dry: 3-4 hours |
| Solid Matter by Content | By volume: 52.2% By mass: 70.5% |
| 150-200 microns | |
| Spreading Rate | 0.5-2 square Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 0.5-1 square |
| Surface Appearance | Smooth, textured finish |
Product Features
• Highly durable and UV resistant.
• Textured effect to hide surface imperfections.
• Water resistant.
• Excellent adhesion.
• Highly flexible coating system, moves with the substrate, covers small plaster cracks and hides blemishes on the plaster surface. This flexibility will remain for many years due to the special elastic grade of acrylic resin emulsion used.
• Excellent application properties.
• Quick drying – 2 coats can be applied in one day.
• Two coats of NEO Plast are required for best results.
• Low odour.
• If correctly applied to a properly prepared substrate the product has a life expectancy of 7-10 years, possibly longer.
Application Details
| • Mixing | The coat has a |
| • Application Method | A combination of |
| • Thinning | Under no circumstances may the product be diluted. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Two coats of NEO Plast are required for best results. • Apply one generous coat with a sheep skin roller of NEO Plast. • Allow to dry 4-6 hours before recoating. • Apply a second thin coat with a textured roller of NEO Plast. • If required, NEO Plast can be overcoated with NEO Dur (ep00) in a wide range of shades and to give added protection. • NEO Plast may under no circumstances be diluted. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 0.5-1 square • Clean up application equipment with clean tap water. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Surface Preparation
| • Mild Steel (Renovation) | • Clean affected areas back to bright metal. • Spot prime with NEO Corroguard (cg00). • Apply one generous coat with a sheep skin roller of NEO Plast. • Allow • Apply a second thin coat with a textured roller of NEO Plast. |
| • Mild Steel (New) | • Degrease surfaces with NEO Metal Conditioner (mc00) to remove the manufacturer’s grease protective layer. This process is repeated until the surface is water break free. • After drying, the whole substrate is coated with NEO Corroguard (cg00). • Apply one generous coat with a sheep skin roller of NEO Plast. • Allow • Apply a second thin coat with a textured roller of NEO Plast. |
| • Dry, Uncoated Concrete Surfaces • Raw Plaster • Precast |
• Make sure • Remove all dust, foreign material, fungal and algae growth. • Prime with NEO Acrylic Wall Primer (ap00). • Repair any cracks, holes • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • Apply one generous coat with a sheep skin roller of NEO Plast. • Allow • Apply a second thin coat with a textured roller of NEO Plast. |
| • Fibre Cement Surfaces (Unc |
• Remove dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Apply one coat of NEO Acrylic Wall Primer (ap00). • Apply one generous coat with a sheep skin roller of NEO Plast. • Allow to dry 4-6 hours before recoating. • Apply a second thin coat with a textured roller of NEO Plast. |
| • Previously Painted Surfaces • Precast |
• Make sure old paint coatings are firm and solid. • Check the adhesion on the substrate. • Remove all loose, flaking and bubbling paint. • Remove all dust, grease, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Repair any cracks, holes • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one generous coat with a sheep skin roller of NEO Plast. • Allow • Apply a second thin coat with a textured roller of NEO Plast. |
Colour Range and Quantities
• NEO Plast is available in a limited range of shades in minimum batch quantities.
• Available in 5
Precautions
• NEO Mica Plast is not flammable.
• The product contains no toxic or harmful substances.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
MULTI DUR
MATT ACRYLIC EMULSION
NM00
New generation water-based 100% acrylic (pure acrylic), high-quality interior/exterior, matt coating. Meets the rigorous requirements of SABS 1586-2, Grade 2.
Application Areas
• Interior and exterior use.
• High traffic areas that need a highly washable and durable coating in a wide range of
• Primed plaster, hardboard, ceilings, fiber cement, galvanized gutters and down pipes, PVC pipes
• Primed metal and wooden substrates.
Product Features
• Durable and UV resistant.
• Washable, comfortably meets the requirements of the very harsh SABS and ASTMS scrubs resistant test methods.
• Excellent adhesion to properly prepared substrates.
• High opacity/hiding power.
• Low odour.
• Two coats of NEO Multi Dur are applied for best results.
• If correctly applied to a properly prepared substrate the product has a life expectancy of 5 to 7 years, possibly longer.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | Brush, roller or airless spray. |
| • Thinning | NEO Multi Dur is ready for use un-thinned; thinning with water will reduce its hiding power. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Two coats of NEO Multi Dur are applied for best results. • With brush, roller or airless spray, apply a generous coat of NEO Multi Dur. • Allow to dry 2-3 hours before recoating. • Apply a second generous coat of NEO Multi Dur. • NEO Multi Dur is ready for use un-thinned; thinning with water will reduce its hiding power. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 8-10 square metres per litre for the first coat and 10-12 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates. • Clean up application equipment with clean tap water. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Surface Preparation
| • Mild Steel (Renovation) | Always stir well before use with a flat paddle. |
| • Application Method | Brush, roller or airless spray. |
| • Thinning | NEO Multi Dur is ready for use un-thinned; thinning with water will reduce its hiding power. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Two coats of NEO Multi Dur are applied for best results. • With brush, roller or airless spray, apply a generous coat of NEO Multi Dur. • Allow to dry 2-3 hours before recoating. • Apply a second generous coat of NEO Multi Dur. • NEO Multi Dur is ready for use un-thinned; thinning with water will reduce its hiding power. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 6-8 square metres per litre for the first coat and 8-10 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates. • Clean up application equipment with clean tap water. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Colour Range and Quantities
• NEO Multi Dur is available in a range of popular
• Available in 5
Precautions
• NEO Multi Dur is not flammable.
• Contains no toxic substances and very low levels of VOC (EU regulations).
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
NATURAL
NN00
New generation water-based, interior/exterior, long-life, flexible textured coating.
Application Areas
• Interior and exterior use.
• Long-life exterior protection of buildings.
• Ideal long-life coating for exterior walls. The coating is highly suitable for use in coastal regions as well as for inland conditions.
• Used as a feature on interior walls.
• New or weathered cement tiles.
• New or weathered fibre cement sheeting.
• New or weathered plaster.
Product Features
• Highly durable and UV resistant.
• Slightly coarse sand filled textured effect to hide surface imperfections. The coating remains flexible and will not show smaller cracks for years to come.
• Highly weather resistant, tough coating, which reflects harmful UV light and prevents rain and humidity penetration into the substrate.
• Water resistant.
• Excellent adhesion.
• Excellent application properties.
• Textured coating suitable for roller application.
• Quick drying, 2 coats can be applied in one day.
• Two coats of NEO Natural are required for best results.
• Low odour.
• If correctly applied to a properly prepared substrate, the product has a life expectancy of 7-10 years, possibly longer.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | A combination of a yellow textured roller or sheepskin roller and/or a block brush. |
| • Thinning | NEO Natural is ready for use un-thinned; thinning with water will reduce its hiding power and its texture. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Two coats of NEO Natural are required for best results. • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. • Apply a second coat in the same manner as the first. • NEO Natural is ready for use un-thinned; thinning with water will reduce its hiding power and its texture. • Clean up application equipment with clean tap water. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Surface Preparation
| • Mild Steel (Renovation) | • Clean affected areas back to bright metal. • Spot prime with NEO Corrotec (ct00). • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. • Apply a second coat in the same manner as the first. |
| • Mild Steel (New) | • Degrease surfaces with NEO Metal Conditioner (mc00)to remove the manufacturer’s grease protective layer. This process is repeated until the surface is water break free. • After drying, the whole substrate is coated with NEO Corrotec (ct00). • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. • Apply a second coat in the same manner as the first. |
| • Fibre Cement Surfaces (Uncoated, Weathered or New) | • Make sure surface is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Apply one coat of NEO Acrylic Wall Primer (ap00). • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. • Apply a second coat in the same manner as the first. |
| • Raw Plaster • Dry, Uncoated Concrete Surfaces • Precast |
• Make sure plaster is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Apply one coat of NEO Acrylic Wall Primer (ap00). • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. Apply a second coat in the same manner as the first. |
| • Previously Painted Surfaces • Precast |
• The existing PVA emulsion paint coating should be of good quality and must have a good bond to the substrate. • Check the adhesion of the substrate. • Remove all loose, flaking and bubbling paint. • Remove all dust, grease, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. • Apply a second coat in the same manner as the first. |
Colour Range and Quantities
• NEO Natural is available in a limited range of shades only.
• Available in 5
Precautions
• NEO Natural is not flammable.
• The product contains no toxic or harmful substances.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
PLAST
TEXTURED COATING
NP00
New generation water-based, interior/exterior, long-life, flexible textured coating.
Application Areas
• Interior and exterior use.
• Long-life exterior protection of buildings.
• Ideal long-life coating for exterior walls. The coating is highly suitable for use in coastal regions as well as for inland conditions.
• Used as a feature on interior walls.
• New or weathered cement tiles.
• New or weathered fibre cement sheeting.
• New or weathered plaster.
Product Features
• Highly durable and UV resistant.
• Slightly coarse sand filled textured effect to hide surface imperfections. The coating remains flexible and will not show smaller cracks for years to come.
• Highly weather resistant, tough coating, which reflects harmful UV light and prevents rain and humidity penetration into the substrate.
• Water resistant.
• Excellent adhesion.
• Excellent application properties.
• Textured coating suitable for roller application.
• Quick drying, 2 coats can be applied in one day.
• Two coats of NEO Natural are required for best results.
• Low odour.
• If correctly applied to a properly prepared substrate, the product has a life expectancy of 7-10 years, possibly longer.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | A combination of a yellow textured roller or sheepskin roller and/or a block brush. |
| • Thinning | NEO Natural is ready for use un-thinned; thinning with water will reduce its hiding power and its texture. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Two coats of NEO Natural are required for best results. • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. • Apply a second coat in the same manner as the first. • NEO Natural is ready for use un-thinned; thinning with water will reduce its hiding power and its texture. • Clean up application equipment with clean tap water. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Surface Preparation
| • Mild Steel (Renovation) | • Clean affected areas back to bright metal. • Spot prime with NEO Corrotec (ct00). • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. • Apply a second coat in the same manner as the first. |
| • Mild Steel (New) | • Degrease surfaces with NEO Metal Conditioner (mc00)to remove the manufacturer’s grease protective layer. This process is repeated until the surface is water break free. • After drying, the whole substrate is coated with NEO Corrotec (ct00). • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. • Apply a second coat in the same manner as the first. |
| • Fibre Cement Surfaces (Uncoated, Weathered or New) | • Make sure surface is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Apply one coat of NEO Acrylic Wall Primer (ap00). • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. • Apply a second coat in the same manner as the first. |
| • Raw Plaster • Dry, Uncoated Concrete Surfaces • Precast |
• Make sure plaster is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Apply one coat of NEO Acrylic Wall Primer (ap00). • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. Apply a second coat in the same manner as the first. |
| • Previously Painted Surfaces • Precast |
• The existing PVA emulsion paint coating should be of good quality and must have a good bond to the substrate. • Check the adhesion of the substrate. • Remove all loose, flaking and bubbling paint. • Remove all dust, grease, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • With a sheepskin roller apply a generous coat of NEO Natural and, if a more textured look is required, use a foam roller to create texture or block brush for Moroccan effect. • Allow to dry 4-6 hours before recoating. • Apply a second coat in the same manner as the first. |
Colour Range and Quantities
• NEO Natural is available in a limited range of shades only.
• Available in 5
Precautions
• NEO Natural is not flammable.
• The product contains no toxic or harmful substances.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
MARBLE PLASTER
TEXTURED COATING
PP00
A new generation of water-based, interior/exterior, long-life structured (textured) wall coating containing marble aggregates. When applied with a textured roller, a regular decorative pattern is achieved.
Application Areas
• Interior and exterior use.
• Walls, plastered and concrete.
• Ceilings, plastered or cast.
• New and weathered cement tiles.
• New and weathered fiber cement sheeting.
• Plaster and previously painted substrates.
• Primed metal and wooden substrates.
Product Features
• Long-life exterior protection of buildings.
• Ideal “cover-up”/sound insulation coating for uneven/blemished ceilings.
• Galvanised metal ceilings can be coated with a decorative textured finish.
• Based on a highly weather, humidity and alkaline resistant acrylic resin emulsion.
• Highly durable and UV resistant.
• Coarse stipple/textured effect to hide surface imperfections.
• Water resistant.
• Excellent adhesion.
• Quick drying – 2 coats can be applied in one day.
• Two coats of NEO Marble Plaster are required for best results.
• Low odour.
• NEO Marble Plaster can always be easily redecorated with NEO Dur (ep00) in all required shades.
• If correctly applied to a properly prepared substrate, the product has a life expectancy of 7-10 years, possibly longer.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | A combination of sheep skin roller and a textured roller. |
| • Thinning | Under no circumstances may the product be diluted. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Two coats of NEO Marble Plaster are required for best results. • Apply one generous coat with a sheep skin roller of NEO Marble Plaster. • Allow to dry 4-6 hours before recoating. • Apply a second thin coat with a textured roller of NEO Marble Plaster. • If required, NEO Marble Plaster can be overcoated with NEO Dur (ep00) in a wide range of shades and to give added protection. • NEO Marble Plaster may under no circumstances be diluted. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 0.5-1 square metres per litre for the first coat and 1-2 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates. • Clean up application equipment with clean tap water. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Surface Preparation
| • Mild Steel (Renovation) | • Clean affected areas back to bright metal. • Spot prime with NEO Corroguard (cg00). • Apply one generous coat with a sheep skin roller of NEO Marble Plaster. • Allow to dry 4-6 hours before recoating. • Apply a second thin coat with a textured roller of NEO Marble Plaster. |
| • Mild Steel (New) | • Degrease surfaces with NEO Metal Conditioner (mc00) to remove the manufacturer’s grease protective layer. This process is repeated until the surface is water break free. • After drying, the whole substrate is coated with NEO Corroguard (cg00). • Apply one generous coat with a sheep skin roller of NEO Marble Plaster. • Allow to dry 4-6 hours before recoating. • Apply a second thin coat with a textured roller of NEO Marble Plaster. • No primer is required inland. |
| • Dry, Uncoated Concrete Surfaces • Raw Plaster • Precast |
• Make sure surface is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Prime with NEO Acrylic Wall Primer (ap00). • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • Apply one generous coat with a sheep skin roller of NEO Marble Plaster. • Allow to dry 4-6 hours before recoating. • Apply a second thin coat with a textured roller of NEO Marble Plaster. |
| • Fibre Cement Surfaces (Uncoated, Weathered or New) | • Remove dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Apply one coat of NEO Acrylic Wall Primer (ap00). • Apply one generous coat with a sheep skin roller of NEO Marble Plaster. • Allow to dry 4-6 hours before recoating. • Apply a second thin coat with a textured roller of NEO Marble Plaster. |
| • Previously Painted Surfaces • Precast |
• Make sure old paint coatings are firm and solid. • Check the adhesion on the substrate. • If there is any doubt regarding the quality of the existing coating (old coatings may lose adhesion due to the heavy textured coating), refrain from applying NEO Marble Plaster. • Remove all loose, flaking and bubbling paint. • Remove all dust, grease, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one generous coat with a sheep skin roller of NEO Marble Plaster. • Allow to dry 4-6 hours before recoating. • Apply a second thin coat with a textured roller of NEO Marble Plaster. |
Colour Range and Quantities
• NEO Marble Plaster is available in a limited range of shades in minimum batch quantities.
• Available in 5
Precautions
NEO Marble Plaster is not flammable and contains no toxic substances.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
REIBEPUTZ
TEXTURED COATING
RP00
New generation water-based, interior/exterior, long-life, structured scratch plaster type coating containing distinct scratch marks. Scratch plaster is a thick coat plaster.
Application Areas
• Interior and exterior use.
• Long-life exterior protection of buildings.
• Used as a feature on interior walls.
• New or weathered cement tiles.
• New or weathered fibre cement sheeting.
• New or weathered plaster.
• Previously painted substrates.
• Primed metal and wooden substrates.
Product Data
| Resin Base | Acrylic emulsion with marble and quartz aggregates |
| Drying Time | Touch dry: ± 60 minutes Hard dry: 3-4 hours |
| Film Thickness | Depends on application |
| Spreading Rate | 0.6-0.7 square metres per litre |
| Surface Appearance | Scratch plaster type coating containing distinct scratch marks. |
Product Features
• Highly durable and UV resistant.
• Forms a hard, solid, nearly indestructible coating for interior and exterior plastered walls.
• Distinct scratch marks provide an attractive appearance.
• Scratch plaster effect to hide surface imperfections.
• Water resistant.
• Excellent adhesion.
• Quick drying.
• Low odor.
• One coat of NEO Reibeputz is required for best results. But the applicator must be an experienced plasterer or poor results will be achieved.
• If correctly applied to a properly prepared substrate, the product has a life expectancy of 7-10 years, possibly longer.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | With trowel only by an experienced plasterer. |
| • Thinning | Under no circumstances may the product be diluted. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • To be applied by trowel only. • NEO Reibeputz may under no circumstances be diluted. • One coat of NEO Reibeputz is required for best results. But the applicator must be an experienced plasterer or poor results will be achieved. • NEO Reibeputz must be applied with strokes in the same direction otherwise an irregular pattern will be achieved. • Allow to dry over night before recoating. • During application it is quite possible that some scratch marks penetrate the coating right to the substrate and the substrate may become visible. For this reason we recommend to prime the plaster with a coat of NEO Dur (ep00) tinted in the same shade as the successive coat of NEO Reibeputz. • Clean up application equipment with clean tap water. • If required, NEO Reibeputz can be overcoated with NEO Dur (ep00) in a wide range of shades to give added protection. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. |
Surface Preparation
| • Mild Steel (Renovation) | • Clean affected areas back to bright metal. • Spot prime with NEO Corroguard (cg00). • Apply one coat of NEO Reibeputz. • NEO Reibeputz must be applied with strokes in the same direction otherwise an irregular pattern will be achieved. |
| • Mild Steel (New) | • Degrease surfaces with NEO Metal Conditioner (mc00) to remove the manufacturer’s grease protective layer. This process is repeated until the surface is water break free. • After drying, the whole substrate is coated with NEO Corroguard (cg00). • Apply one coat of NEO Reibeputz with a trowel. • NEO Reibeputz must be applied with strokes in the same direction otherwise an irregular pattern will be achieved. |
| • Dry, Uncoated Concrete Surfaces • Fibre Cement Surfaces (Uncoated, Weathered or New) • Raw Plaster • Precast |
• Make sure surface is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Prime with NEO Acrylic Wall Primer (ap00). • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • Apply one coat of NEO Reibeputz with a trowel. • NEO Reibeputz must be applied with strokes in the same direction otherwise an irregular pattern will be achieved. |
| • Previously Painted Surfaces • Precast |
• We do not recommend the application of NEO Reibeputz on previously painted surfaces, because the old coating may loose adhesion and will accordingly not be able to carry the coating of NEO Reibeputz. • Make sure old paint coatings are firm and solid. • Check the adhesion of the substrate. • Remove all loose, flaking and bubbling paint. • Remove all dust, grease, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Apply one coat of NEO Reibeputz with a trowel. • NEO Reibeputz must be applied with strokes in the same direction otherwise an irregular pattern will be achieved. |
Colour Range and Quantities
• NEO Reibeputz is available in a limited range of shades in minimum batch quantities.
• Available in 20 litres.
Precautions
• NEO Reibeputz is not flammable.
• Contains no toxic substances.
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
DUR EGGSHELL
SG00
A new generation polyurethane/alkyd based, long-life, interior, the silky eggshell coating that meets the rigorous specifications of SABS 515-2 for eggshell and matt finishes.
Application Areas
• Interior use only.
• High traffic and exterior areas that need a highly washable and scratch resistant coating in a wide range of colours.
• Truly universal product, for walls as well as furniture, doors etc.
• The coating can be used on walls, kitchen cupboards, wardrobes, doors, window frames and other objects.
• Primed plaster, hardboard and fibre cement walls.
• Primed metal and wooden substrates.
• Suitable for exterior use in covered up areas – weather resistance is not equal to the resistance of a high gloss finish.
Product Features
• Highly washable, cleanable, humidity and scratch resistant.
• Can be cleaned with the usual household detergents without damage to the surface.
• Excellent adhesion to a range of properly prepared substrates.
• High hiding power and film build.
• Based on an alkyd polyurethane resin combination, which contains special matting agents to give a silky and smooth surface.
• Combines the general characteristics of PVA paints, namely slight gloss with the durability and surface hardness of high gloss enamel paint.
• The product dries to a very hard and scratch resistant finish, whilst still remaining flexible.
• Two coats of NEO Dur Eggshell are applied for best results.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | Brush, short hair roller or airless spray. |
| • Thinning | NEO Dur Eggshell is ready for use un-thinned; thinning will reduce its hiding power. Only for spray application thin 20% with NEO Mineral Turpentine (mt00). |
| • Cleaning | NEO Mineral Turpentine (mt00). |
| • Application | • Stir well before use. • Two coats of NEO Dur Eggshell are applied for best results. • With brush, roller or airless spray, apply a generous coat of NEO Dur Eggshell. • Allow to dry 18-24 hours before recoating. • With brush, roller or airless spray, apply a second generous coat of NEO Dur Eggshell. • NEO Dur Eggshell is ready for use un-thinned; thinning will reduce its hiding power. For spray application thin 20% with NEO Mineral Turpentine (mt00). • Clean up application equipment with NEO Mineral Turpentine (mt00). • Only apply in ventilated areas, keep away from all ignition sources, flames and sparks. • Do not eat, drink or smoke while applying. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 8-10 square metres per litre for the first coat and 10-12 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates. • For interior use only. |
Surface Preparation
| • Mild Steel (Renovation) | • Affected areas need to be cleaned back to bright metal and spot primed with NEO Corroguard (cg00), NEO Corrotec (ct00) or NEO Zinc Chromate (zc00). • Apply one coat of NEO Universal Undercoat (wu00). • With brush, roller or airless spray, apply a generous coat of NEO Dur Eggshell. • Allow to dry 18-24 hours before recoating. • With brush, roller or airless spray, apply a second generous coat of NEO Dur Eggshell. |
| • Mild Steel (New) | • Degrease surfaces with NEO Metal Conditioner (mc00) to remove the manufacturer’s grease protective layer. This process is repeated until the surface is water break free. • After drying, the whole substrate is coated with NEO Corroguard (cg00), NEO Corrotec (ct00) or NEO Zinc Chromate (zc00). • Apply one coat of NEO Universal Undercoat (wu00). • With brush, roller or airless spray, apply a generous coat of NEO Dur Eggshell. • Allow to dry 18-24 hours before recoating. • With brush, roller or airless spray, apply a second generous coat of NEO Dur Eggshell. |
| • Fibre Cement Surfaces (Uncoated, Weathered or New) | • Remove dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • Apply one coat of NEO Acrylic Wall Primer (ap00). • With brush, roller or airless spray, apply a generous coat of NEO Dur Eggshell. • Allow to dry 18-24 hours before recoating. • With brush, roller or airless spray, apply a second generous coat of NEO Dur Eggshell. |
| • Raw / New Plaster • Dry, Uncoated Concrete Surfaces |
• Make sure surface is firm and completely dry. • Remove all dust, foreign material, fungal and algae growth. • Apply one coat of NEO Acrylic Wall Primer (ap00). • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • With brush, roller or airless spray, apply a generous coat of NEO Dur Eggshell. • Allow to dry 18-24 hours before recoating. • With brush, roller or airless spray, apply a second generous coat of NEO Dur Eggshell. |
| • Previously Painted Surfaces | • Make sure old paint coatings are firm and solid. • Remove all loose, flaking and bubbling paint. • Remove all dust, grease, foreign material, fungal and algae growth. • Sand glossy coatings until reasonably matt. • Repair any cracks, holes and blemishes with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Allow to dry. • After drying over night, all primed areas and previously painted areas must be coated with NEO Universal Undercoat (wu00). • With brush, roller or airless spray, apply a generous coat of NEO Dur Eggshell. • Allow to dry 18-24 hours before recoating. • With brush, roller or airless spray, apply a second generous coat of NEO Dur Eggshell. |
| • Wood, Chipboard and other Fibre Boards • Hard Board |
• Prime wood boards with one coat of NEO Universal Undercoat (wu00). • Sand if required until smooth and remove dust with a moist cloth. • With brush, roller or airless spray, apply a generous coat of NEO Dur Eggshell. • Allow to dry 18-24 hours before recoating. • With brush, roller or airless spray, apply a second generous coat of NEO Dur Eggshell. |
Colour Range and Quantities
• NEO Dur Eggshell is available in a range of popular ready-mixed colors and on the NEO ColourWorks tinting system.
• Available in 1 liter, 5 liters, and 20 liters.
Precautions
• NEO Dur Eggshell is highly flammable and has a flashpoint of 37 degrees Celsius.
• Use only in
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.
TEFLACRYL
TEFLON BASED ACRYLIC EMULSION
TC00
A new generation, water-based, 100% acrylic, quality interior/exterior, semi-gloss, sheen coating.
Application Areas
• Interior and exterior use.
• High traffic areas that need a highly washable and durable coating in a wide range of
• Plaster, concrete, hardboard and
• Due to the high degree of dirt repellence, NEO Teflacryl is the ideal coating for public buildings, schools, hotels
• New plaster (very alkaline) can be coated with NEO Teflacryl successfully.
• Can be applied directly on to most substrates and existing paint coatings.
• For the application on steel, it is essential to apply a suitable primer.
• NEO Teflacryl can be applied on degreased,
• NEO Teflacryl can not be applied on un-primed steel.
Product Data
| Resin Base | Acrylic resin emulsion |
| Drying Time | Touch dry : 30-60 minutes Hard dry: 3–4 hours |
| Solid Matter by Content | By volume: 36.5% By mass: 50% |
| Film Thickness | 35-40 microns |
| Spreading Rate | 8-12 square Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 8-10 square |
| Surface Appearance |
Product Features
• Highly durable and UV resistant.
• Highly dirt repellent.
• Highly washable, comfortably meets the requirements of the very harsh SABS and ASTMS scrubs resistant test methods.
• Excellent adhesion.
• Low odor.
• Smooth, velvet touch and a silky finish, which makes it a viable option to solvent-based eggshell enamel finishes.
• Excellent exterior durability both in coastal and inland conditions – highly humidity and water-resistant.
• Two coats of NEO Teflacryl are applied for best results.
• If correctly applied to a properly prepared substrate, the product has a life expectancy of 7-10 years, possibly longer.
Application Details
| • Mixing | Always stir well before use with a flat paddle. |
| • Application Method | Brush, roller or airless spray. |
| • Thinning | NEO Teflacryl is ready for use un-thinned; thinning with water will reduce its hiding power. |
| • Cleaning | Water. |
| • Application | • Stir well before use. • Two coats of NEO Teflacryl are applied for best results. • With brush, roller or airless spray, apply a generous coat of NEO Teflacryl. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Teflacryl. • Do not apply before 09:00 and after 16:00 in the winter. • Do not apply exterior if it looks like rain will occur within 4-6 hours of application. • NEO Teflacryl is ready for use un-thinned; thinning with water will reduce its hiding power. • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 8-10 square metres per litre for the first coat and 10-12 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates. • Clean up application equipment with clean tap water. |
Surface Preparation
| • Mild Steel (Renovation) | • Affected areas need to be cleaned back to bright metal and spot primed with NEO Corroguard (cg00). • Sand existing coating. • With brush, roller or airless spray, apply a generous coat of NEO Teflacryl. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Teflacryl. |
| • Mild Steel (New) | • Degrease surfaces with NEO Metal Conditioner (mc00)to remove the manufacturer’s grease protective layer. This process is repeated until the surface is water break free. • After drying, the whole substrate is coated with NEO Corroguard (cg00). • With brush, roller or airless spray, apply a generous coat of NEO Teflacryl. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Teflacryl. |
| • Uncoated Concrete Surfaces • Raw / New Plaster • Precast |
• Make sure surface is dry and firm. • Remove all dust, foreign material, fungal and algae growth. • Prime with NEO Acrylic Wall Primer (ap00). • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Sand well and remove dust. • With brush, roller or airless spray, apply a generous coat of NEO Teflacryl. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Teflacryl. |
| • Uncoated, Weathered or New Fibre Cement Surfaces | • Remove dust, foreign material, fungal and algae growth. • If friable or powdery, seal with NEO Bonding Liquid (ig00). • With brush, roller or airless spray, apply a generous coat of NEO Teflacryl. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Teflacryl. |
| • Wood and Fibre Board (New & Renovation) • Hard Board |
• Prime surfaces with one coat of NEO Pink Primer (pi00). • Repair any blemishes with NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Repair Paste (nrp07). • With brush, roller or airless spray, apply a generous coat of NEO Teflacryl. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Teflacryl. |
| • Previously Painted Surfaces • Concrete • Precast |
• Surface must be in a sound condition. • Existing gloss finishes should be well sanded. • Remove all loose, flaking and bubbling paint. • Remove all dust, foreign material, fungal and algae growth. • Allow to dry. • Fill and seal all visible cracks with NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Apply one coat of NEO Bonding Liquid (ig00) to cover NEO Aurora Filler (ef00) or NEO Repair Paste (nrp07). • Prime the bare and visible plaster areas with NEO Acrylic Wall Primer (ap00). • With brush, roller or airless spray, apply a generous coat of NEO Teflacryl. • Allow to dry 4-6 hours before recoating. • Apply a second generous coat of NEO Teflacryl. |
Colour Range and Quantities
• NEO Teflacryl is available in a range of popular,
• Deep and bright shades can be manufactured on request.
• Available in 5 litres and 20 litres.
Precautions
• NEO Teflacryl is not flammable.
• Contains no toxic substances and only very small amounts of organic solvents.
• Low levels of VOC (EU regulations).
Disclaimer
NEO Paints can not be held liable if the product fails due to improper surface preparation or application.